Ip Configuration

In: Computers and Technology

Submitted By fmcintosh12
Words 321
Pages 2
For the network configuration, we decided to go with a partial mesh configuration to save on cost and time. With the amount of staff members and estimate growth on a annual basis. For Ip address that’s needed to allow enough for employees and guest for the business the sufficient. ip address 10.0.0.0.0 with 255.255.255.255 subnet with 256 usable ip address with a /25 allow guest to use the network .
The configuration of the wireless network would allow the management workgroup to connect wireless on the third floor were the upper management staff. Basement level to the second/ first floor with run unshielded paired Ethernet cabling only to the telemarketers, which is about 85 feet. 15 ft for the security desk and 20 feet to training room. Sales agents will run off the wireless with workgroup allowing minimal access to display product to customers with restricted access to the outside internet with the configurations to allow monitor and packet captures as well as the management group .wireless system will support IEEE 802.11g ,IEEE 802.11b, IEEE 802.11a. Cisco wireless access point will be mounted on the ceiling with a hexagon formation to allow maximum coverage within the infrastructure. Basic information relating to the communication of the wireless network in figure 1.1 and the layout of the cisco wireless access points figure 1.2. each workstation not part of the training or security will be equipped with 150Mbps 2.4GHz Wireless PCI LAN Adapter Card with Antenna which will connect with access point located around the building.
Base of the network will run a partial mesh topology for the sales for and the telemarketers on the second floor
For the wireless set up a guest network would need to establish internet access and reference point complexly different from the sales floor access.
Basic network configurations for cisco wireless access…...

Similar Documents

Deterining Subnet Configuration

...Running head: DETERMINING SUBNET CONFIGURATION Determining Subnet Configuration for Variety of Networks Alvin Miles AIU Online 09/20/2012 Determining Subnet Configuration for Variety of Networks In this final week IP assignment we are given some IP addresses and are ask several questions on anything from what is the broadcast address of this IP, what are the range of valid host IP addresses, to subnet ranges. Before we go too deep in trying to answer these questions I must first explain what classful routing protocol is as this will help explain some of my answers. In classful routing protocol all your networks will be using different classes and are separated only by a router (Lewis, 2011). Also classful routing protocol will only look at IP addresses and not the subnet mask. This is a problem as you can’t change the subnet mask in any of your network (Lewis, 2011). Most networks today use the classless routing protocol. This protocol supports VLSM and different sizes network within the same IP address class (Lewis, 2011). The first IP address we are given is 12.2.201.2, from this we are ask the question of what is the network address or network number? The network address would fall within the Class “A” and would give us 12.0.0.0. The second question asks us to find out what the broadcast address of the IP address 211.106.32.0 that has a subnet mask of 255.255.255.224. To get the broadcast address we will need to find out how many subnets and hosts that......

Words: 1211 - Pages: 5

Cisco Switch Configuration

...Router>en Enter the configuration mode: Router#configure terminal Define the hostname (the name router is changed to Ciscozine) Router(config)#hostname Ciscozine Ciscozine(config)# Assign the privileged level secret The enable secret password allows you to enter enable mode (sometimes referred to as privileged mode or privileged-EXEC mode). To set a secret password: Enable administrative privilege Ciscozine>en Enter the configuration mode: Ciscozine#configure terminal Define the privileged-EXEC mode password; remember to use a strong password (combine letters, numbers, nd symbols). The enable secret command uses a one-way encryption hash based on Message Digest 5 (MD5) Ciscozine(config)#enable secret C1sc0z$n3 Secure console port For security reasons, you must define a console password: Enable administrative privilege Ciscozine>en Enter the configuration mode: Ciscozine#configure terminal Enter in the console configuration Ciscozine(config)#line console 0 Define your console password Ciscozine(config-line)#password g4S$%A2 Enable the password defined Ciscozine(config-line)#login Use the “logging synchronous” command, so the messages appear only after you press Return Ciscozine(config-line)#logging synchronous Secure VTY lines For security reasons, you must define a vty line password. The vty lines defines the password needed for a remote access (telnet, ssh, …) Enable administrative privilege Ciscozine>en Enter the configuration......

Words: 621 - Pages: 3

Dynamic Host Configuration Protocol

...In simple terms, DHCP determines if your IP is static or dynamic and the length of time an IP address is assigned. Dynamic Host Configuration Protocol is controlled by a DHCP server. Your router can be a DHCP server…and if you’re on a home network, it most likely serves this purpose. Read more: http://www.whatismyip.com/ip-faq/what-is-dhcp/#ixzz2SFrnB7wR I know this might be confusing because the word dynamic is in the term, but just because you have DHCP enabled on your computer doesn’t mean you can’t be assigned a static IP. DHCP enabled on your computer simply means you’re letting a DHCP server assign its IP. Having it enabled DOES NOT mean it’s a DHCP server. A true DHCP server (not your Linksys router) gives the LAN Admin a ton of control with IP assigning. Ever print to a network printer? Ever wonder how that printer keeps its network assignment? Each network device has a MAC address. You can assign a static IP at the server to a specific MAC address. This allows the network printer to always get the same IP even after it reboots and without assigning the IP at the printer. If you print the network configuration at the printer, it will probably tell you that DHCP is enabled and no static IP is assigned. That’s because the IP assignment is handled at the server. Your ISP has a DHCP server. They can assign IPs by modem MAC addresses. When your modem comes online, it communicates to the network indicating it is looking for an IP address. The DHCP server listens to......

Words: 425 - Pages: 2

Nat Configuration

...Software Release 12.2 (10b) The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command. Conventions Refer to Cisco Technical Tips Conventions for more information on document conventions. Quick Start Steps for Configuring and Deploying NAT When you configure NAT, it is sometimes difficult to know where to begin, especially if you are new to NAT. These steps guide you to define what you want NAT to do and how to configure it: 1. Define NAT inside and outside interfaces. ♦ Do users exist off multiple interfaces? ♦ Are there multiple interfaces going to the internet? 2. Define what you're trying to accomplish with NAT. ♦ Are you trying to allow internal users to access the internet? ♦ Are you trying to allow the internet to access internal devices (such as a mail server or web server)? ♦ Are you trying to redirect TCP traffic to another TCP port or address? ♦ Are you using NAT during a network transition (for example, you changed a server's IP address and until you can update all the clients you want the non−updated clients to be able to access the server using the original IP address as well as allow the updated clients to access the server using the new address)? ♦ Are you using NAT to allow overlapping networks to communicate? 3. Configure NAT in order to......

Words: 3234 - Pages: 13

Switch Configuration

...Switch Configuration Switch Configuration First I would unpack the switch along with all of its contents, check for any missing or damaged items and if any our found I would then contact the cisco team but if everything looks great I would then proceed. If I have all the equipment ready for the switch I would then continue on with what they call the express set up. First thing I would do is verify that no devices are connected to the switch when first initializing the setup the switch will start acting like a DHCP server. Since my network has a static IP address I will change it for the time being to DHCP. Once switch is mounted and I have all my devices prepared for it I will then power it on. As the POST initializes I can get a good indication that the switch is functioning properly. I can tell when the POST is complete by SYSLED blinking green and if it fails it would blink an amber color. Next with my laptop I will hook directly in to the switch via CAT5. From there I will log in to the switch by opening my web browser and in the address bar typing in the IP address of the switch, which by default is 10.0.0.1 then you will enter the express setup GUI will open. In the express setup GUI I will configure my VLAN ID, IP, and IP subnet mask then I will enter my routers IP to point the switch through my default gateway. Then I will enable Telnet and set the Telnet password this will allow me to access and manage my switch using the command line interface (CLI). I can...

Words: 585 - Pages: 3

Switch Configuration

...(DrPeering, 2013); A Tier2 ISP that purchases transit to reach destinations within an Internet Region (DrPeering , 2013). The basic requirements to run an ISP is having a solid backbone T1, 2 or 3; you will also need an Ethernet switch, an upstream router, a remote access server, and a local server for DNS and RADIUS (Patton Electronics, 2009). There are network layers associated ISP which consist of the Application Layer (Telnet, HTTP, FTP, SMTP), Transport Layer (TCP, UDP), Network Layer (IP), and the Physical Layer (Ethernet, X25, Token Ring). The application layer is reserved for communication protocols and methods designed for process to process communications across an IP (Internet Protocol) computer network. The Transport Layer provides convenient services such as connection oriented data stream support, reliability, flow control and multiplexing. The most common form of the transport protocol is the transmission control protocol (TCP) part of the entire Internet Protocol Suite TCP/IP is used for connection oriented transmissions. The Network Layer is used for packet forwarding including routing through routers in other words its responsible for sending data from a source to its destination. The Physical Layer is all networking hardware such as NIC’s, Modems, Hubs, Repeaters etc. (Mitchel, 2011). These are just some of the layers that make up the OSI model but are primarily used in ISP’s. References DrPeering (2013, February). What is a Tier 1 ISP? [Web log......

Words: 513 - Pages: 3

Subnet and Router Configuration

...Subnet and Router Configuration Author Note This research is being submitted on August 18th, 2013, for Christine Stagnetto-Zweig’s N235/CET2629 Section 02 Cisco Networking Fundamentals and Routing course. Subnet and Router Configuration Given the IP address 154.78.0.0 calculate the subnet masks that would offer 18 subnets, and have the ability to add 6 per year for the next five years, with each subnet having up to 580 hosts? With This IP address (154.78.0.0) in order to give my client 18 available Subnets also with an option of adding 6 more subnets for the next five years and with each subnet having up to 580 hosts per subnet. I have given this much thought and the subnet mask I would use is 255.255.252.0 this will give me 64 available subnets for growth along with 1,022 hosts per subnet I know that’s a little more than 580 hosts but in my mind having doubled that wouldn’t hurt. This will make my first host IP address be 154.78.0.1 and my last host address be 154.78.3.254 leaving 154.78.3.255 my broadcast address and 154.78.0.0 my network address. Indicate the steps and command that you would use to access and configure the router/switch. Configuring the Fast Ethernet Interface Steps | Command | Purpose | 1 | Router>enable | EXEC Mode, Privileged/pswd | 2 | Router# configure terminal | global configuration mode | 3 | Router# show ip interface brief | brief status of the interfaces that are configured for IP | 4 | Router(config)# interface......

Words: 423 - Pages: 2

Basic Switch Configuration

...Basic Switch Configuration Switch>enable Switch# Examine the current running configuration file. Switch#show running-config Examine the current contents of NVRAM: Switch#show startup-config Examine the characteristics of the virtual interface VLAN1: Switch#show interface vlan1 Switch#show ip interface vlan1 Examine the following version information that the switch reports. Switch#show version Examine the default properties of the FastEthernet interface used by PC1. Switch#show interface fastethernet 0/18 Switch#show vlan examine the contents of the flash directory. Switch#dir flash: or Switch#show flash Switch#dir flash:c2960-lanbase-mz.122-25.SEE3 To save the contents of the running configuration file to non-volatile RAM (NVRAM), issue the the command copy running-config startup-config. Switch#copy running-config startup-config S1#configure terminal S1(config)#hostname S1 S1(config)#exit S1#configure terminal S1(config)#line console 0 S1(config-line)#password cisco S1(config-line)#login S1(config-line)#line vty 0 15 S1(config-line)#password cisco S1(config-line)#login S1(config-line)#exit S1(config)#enable secret class First, you will create the new VLAN 99 on the switch. Then you will set the IP address of the switch to 172.17.99.11 with a subnet mask of 255.255.255.0 on the internal virtual interface VLAN 99. S1(config)#vlan 99 S1(config-vlan)#exit S1(config)#interface vlan99 %LINEPROTO-5-UPDOWN: Line protocol on Interface......

Words: 873 - Pages: 4

Ip Networking

...e. OSPF f. Integrated IS-IS 5. Router1 has interfaces with addresses 9.1.1.1 and 10.1.1.1. Router2, connected to Router1 over a serial link, has interfaces with addresses 10.1.1.2 and 11.1.1.2. Which of the following commands would be part of a complete RIP Version 2 configuration on Router2, with which Router2 advertises out all interfaces, and about all routes? a. router rip b. router rip 3 c. network 9.0.0.0 d. version 2 e. network 10.0.0.0 f. network 10.1.1.1 g. network 10.1.1.2 h. network 11.0.0.0 i. network 11.1.1.2 6. Which of the following network commands, following a router rip command, would cause RIP to send updates out two interfaces whose IP addresses are 10.1.2.1 and 10.1.1.1, mask 255.255.255.0? a. network 10.0.0.0 b. network 10.1.1.0 10.1.2.0 c. network 10.1.1.1 10.1.2.1 d. network 10.1.0.0 2550.255.0.0 e. network 10 f. You cannot do this with only one network command 7. What command(s) list(s) information identifying the neighboring routers that are sending routing information to a particular router? a. show ip b. show ip protocol c. show ip routing-protocols d. show ip route e. show ip route neighbor f. show ip route received   8. Review the snippet from a show ip route command on a router: R 10.1.2.0 [120/1] via 10.1.128.252, 00:00:13, Serial0/0/1 Which of the following statements are true regarding this output? a. The administrative distance is 1. b. The administrative distance is 120. c. The metric is......

Words: 1957 - Pages: 8

Dhcp Server Configuration in Ubuntu

...DHCP Server configuration 1) Configure the network interface to give a static IP address to the DHCP server Edit the file /etc/network/interfaces [pic] 2) Use the command sudo apt-get install isc-dhcp-server in the terminal to install DHCP. 3) For the DHCP to assign Ipv4 addresses edit the file /etc/dhcp/dhcpd.conf and provide the range of address you want to the DHCP server to assign. [pic] 4) For ipv6 address, create a new file dhcpd6.conf and then configure the range of ipv6 addresses which needs to be assigned. The file should be created in /etc/dhcp/dhcpd6.conf [pic] 5) For ipv6, edit the file /etc/sysctl.conf and provide the below configurations. net.ipv6.conf.all.forwarding=1 net.ipv6.conf.all.autoconf=1 net.ipv6.conf.all.accept_ra=1 [pic] 6) Enter the below commands to enable the configurations made above. sudo sysctl -w net.ipv6.conf.all.autoconf=1 sudo sysctl -w net.ipv6.conf.all.accept_ra=1  sudo sysctl -w net.ipv6.conf.all.forwarding=1 7) Install the router advertisement daemon or radvd by using the command Sudo apt-get install radvd 8) Create file /etc/radvd.conf and put the internal interface and prefix there. [pic] 9) Now restart all the service using the commands - Sudo /etc/init.d/networking restart - Sudo /etc/init.d/radvd......

Words: 335 - Pages: 2

Switch Configuration

...| Switch Configuration | | | Amanda Robertson | 4/20/2014 | | I was Hired By a company as a network engineer. One of my first jobs was to purchase, install, configure and deploy a Cisco Catalyst 2960-S Series Switches. This is a popular choice with the LAN Base Software, which comes with the switches. I found that this switch would be compatible with the companies needs having 48 ports, POE configurations that offer up to 15.4w per port, USB storage, 10 GB Ethernet uplink flexibility. This switch would use either copper or fiber optic cabling however I would prefer the fiber optic. The first step that I would have to take is to connect all hardware properly. “When you first set up the switch, you should use Express Setup to enter the initial IP information. This enables the switch to connect to local routers and the Internet. You can then access the switch through the IP address for further configuration” (Cisco, 2006-2010). Plug in the AC adaptor cord to the Cisco switch to power it on. The switch will go through POST and then verify that the SYST LED light blinks green rapidly. To run Express Set up mode, hold the mode button for 3 seconds, or when all lights above mode buttons turns green. Connect a CAT5 Ethernet cable to the switch and computer, after 30 seconds launch a browser and enter the IP address 10.0.0.1 in the browser and press enter. I would then fill out all the information requested by the Express Set up Mode, the Management interface......

Words: 569 - Pages: 3

Internet Protocol Configuration

...ip route 0.0.0.0 0.0.0.0 10.255.255.1 router eigrp 100 network 10.0.0.0 no auto-summary int s0/0/0 ip summary-address eigrp 100 10.1.0.0 255.255.0.0 ip dhcp pool B1_VLAN10 network 10.1.10.0 255.255.255.0 default-router 10.1.10.1 dns-server 10.0.1.4 exit ip dhcp pool B1_VLAN20 network 10.1.20.0 255.255.255.0 default-router 10.1.20.1 dns-server 10.0.1.4 exit ip dhcp pool B1_VLAN30 network 10.1.30.0 255.255.255.0 default-router 10.1.30.1 dns-server 10.0.1.4 exit ip dhcp pool B1_VLAN88 network 10.1.88.0 255.255.255.0 default-router 10.1.88.1 dns-server 10.0.1.4 exit ip dhcp excluded-address 10.1.10.1 10.1.10.10 ip dhcp excluded-address 10.1.20.1 10.1.20.10 ip dhcp excluded-address 10.1.30.1 10.1.30.10 ip dhcp excluded-address 10.1.88.1 10.1.88.24 B2 hostname B2 int s0/0/0 ip address 10.255.255.6 255.255.255.252 no sh encapsulation frame-relay frame-relay lmi-type q933a exit ip route 0.0.0.0 0.0.0.0 10.255.255.5 router eigrp 100 passive-interface fa0/0.10 passive-interface fa0/0.20 passive-interface fa0/0.30 passive-interface fa0/0.99 network 10.0.0.0 no auto-summary int s0/0/0 ip summary-address eigrp 100 10.2.0.0 255.255.0.0 ip dhcp pool B2_VLAN10 network 10.2.10.0 255.255.255.0 default-router 10.2.10.1 dns-server 10.0.1.4 exit ip dhcp pool B2_VLAN20 network 10.2.20.0 255.255.255.0 default-router 10.2.20.1 dns-server 10.0.1.4 exit ip dhcp pool B2_VLAN30 network 10.2.30.0 255.255.255.0 default-router......

Words: 3046 - Pages: 13

Ip Telephony

...Hosted IP Telephony Services Service Offering Nexogy offers a range of market solutions to our clients, serving markets from residential customers to sophisticated business customers with reliable full-featured VoIP applications Our Hosted IP Telephony Services primarlily consist of: • • • IP Centrex/ IP PBX Hosted Business Business Trunking Enhanced Residential IP Centrex / IP PBX • Bring the power of a corporate PBX to enterprise customers who will no longer have to invest in PBX equipment or its maintenance • Works with analog phones as well as with IP Phones • Offer traditional PBX functionality plus a wide range of value added services not economically feasible with traditional solutions • Centralize communications services (National and International Long Distance, Local Calling, Local Phone Service, Hosted PBX) on a single bill IP Centrex Features 976/900 Block Abbreviated 2-digit dialing Anonymous Call Rejection Billing Codes Call Forward All Calls Call Forward Busy Call Forward No Answer Call Return Call Trace Call Waiting Call Waiting/ID Manager Caller ID Caller ID Block Classes of Service Direct Inward Dial (DID) Do Not Disturb Flexible Auto-Attendant Flexible Numbering Plan Forward to Voice Mail Group Pickup Hold Hold Music Hunt Groups Multi-call Park N-way Conference Off-Premises Stations Park & Park Pickup Permanent Per Call Block Priority Call Queues Redial Remote Call Forward to DID Selective Call Forward Selective Call Rejection Speed Dial TAPI...

Words: 1276 - Pages: 6

Nt2670 - Installation and Configuration of Ms

...Server 2008; therefore only a computer capable of running the 64 bit version of 2008. Once that is done named the server (mailitsupport.com), set the clock and it’s configured to be a stand alone with default settings. Configure Your Static IP Address The default installation of Windows 2008 sets your IP v4 and IP v6 addresses to use DHCP.  Since we will be configuring this computer to be a domain controller, you must change the IP address of the computer to be a static IP address which should be done via View Network Connections" in the Server Manager screen.  This will display the list of active network interfaces. a. Double click on your network adaptor to display the adaptors status. b. Press the Properties button. c. Highlight "Internet Protocol Version 4 (TCP/IPv4)" and then press the Properties button. d. Change the radio button to "Use the following IP address" and enter an IP address you want to use for this server. I chose to assign this server the internal IP address "192.168.1.25". The firewall appliance is set as a gateway at the IP address "192.168.1.1".  e. Press OK to save your changes. If IP v6 is needed, follow the same process as in IP v4 or else IP v6 set to the default setting of DHCP. DO NOT DISABLE IP V6 or else the Exchange Hub Transport Service will not start. Activate Auto Update Now activate Domain Controller for auto update by clicking on the link "Configure Updates”; selecting the option to have Windows automatically install......

Words: 2240 - Pages: 9

Ip Array

...Interface and Display IP Configuration Settings Open the Windows Command Prompt using the desktop or the Taskbar icon. Maximize the size of the CLI. Use the ipconfig /all command to determine the following IP configuration settings for “Wired” Ethernet NIC: IP Address: | 192.168.0.1 | Subnet Mask: | 255.255.0.0 | Default Gateway: | 192.168.0.250 | MAC (Physical) Address | 00-50-56-A3-38-89 | Copy and paste the specified ipconfig /all command output from the Windows CLI into the Task 1 box provided below. Task 1 ipconfig /all Command Output Ethernet adapter NIC: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 MT Network Connection Physical Address. . . . . . . . . : 00-50-56-A3-38-89 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::85f6:de97:d45e:9fbd%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.250 DHCPv6 IAID . . . . . . . . . . . : 234884137 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-EE-13-98-00-0C-29-DB-1B-7E DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled | Task 2: Changing Interface Configuration settings from the......

Words: 597 - Pages: 3